ITOP 4-2-601 PDFITOP 4-2-601 PDF

ICS, Doc ID, ITOP Title, Drop Tests for Munitions. Original Title. Category, IS / TS. Location. ITOP Drop Tests for Munitions, Final Report on International Test Operations Procedure. ITOP (2), Safety Testing of Field Artillery Ammunition. – ITOP , Drop Test for Munitions. – ITOP , Rough Handling Tests.

Author: Zulut Zushakar
Country: Azerbaijan
Language: English (Spanish)
Genre: Sex
Published (Last): 28 May 2012
Pages: 340
PDF File Size: 15.71 Mb
ePub File Size: 4.12 Mb
ISBN: 780-7-88883-967-4
Downloads: 99047
Price: Free* [*Free Regsitration Required]
Uploader: Akinobar

Photographs of the rigged configuration. The size of most shelters necessitates the use of forklifts with tines of at least 2. Modem containerships, to include combination ships, are designed to carry all or part of their cargo load in containers. Additional copies are can be requested through the following website: From this comparison an estimate is made regarding the utop of the item to be transported by various types of vessels.

Full text of “DTIC ADA Test Operations Procedure (TOP): Transportability”

On most guns the bolt being closed after the shot will not completely seal off the gas. The Army-type designator M referenced in this specification is of Army origin and does not reflect a particular design See 6.

Provide a recommendation as to the maximum safe speed for EAT of each load configuration and helicopter combination. The cartridge dimensions shall conform to Describe the method and equipment employed to secure the item for each load application. The weapons shall be cleaned and lubricated before firing at each temperature.

  LIBRO 13 ESCALONES DEL MENTALISMO PDF

Amount and type of damage, if any. Engage the parking brakes on vehicles, trailers or weapon systems equipped with parking brake systems. Representative marine tie-down configurations are illustrated in TEA Pamphlet The cartridges will be visually inspected for any signs of deterioration.

Loose cargo packaged vibration rounds. When specified in examinations and tests cited herein; critical, major, and minor characteristics are in accordance with MIL-STD Identification of cargo handling equipment employed, if any. Record and photograph any weld cracking or visible permanent deformation or set in the provision s or other structural component resulting from load application.

Identification of spreader bar s employed, as necessary, and the configuration of the lifting assembly photographs when available. Surveillance No fumes in less than 30 days of storage at For Design Verification testing, the cartridges and weapons shall be tested at hot, cold, and ambient temperatures.

MIL-PRF-32300

Specific vehicle configuration standards are defined in Military and Federal standards. TOP 15 September C. The cleaning method used shall not be injurious to any parts, nor shall the parts be contaminated by any cleaning agent. The first article sample shall be rejected if the requirement is not met. Materiel itpp any of the following conditions: Flight at this or higher air speed is not recommended. The verification requirements specified herein are classified as follows: Employ data obtained from the lift and tie-down attachments ifop para 4.

  GIMNASIA HIPOPRESIVA PDF

Load, block, brace, and tie down the item on a semitrailer or other vehicle designated as the prime mover. Load is uncontrollable for most or all of the maneuvers. The composite two-wheeled trailer vibration environment shall simulate 25 km 16 mi.

Maintenance tools and equipment repair shops, tool sets, etc. The objectives of this sub test are to determine the ability of: Static pull test results Paragraph 4. Vertical distance between item and ground ground impact test.

cover.PDF Adrienne Cantler

Remington – Ambient f. A wooden retaining fence section shall be placed around the perimeter of a section of the bed of the package tester to prevent the ammunition containers from falling off the table and shall be positioned so that free space of approximately 25mm exists on all sides of the packaged ammunition. For the longitudinal axis, packaged ammunition shall be placed on the table with the longitudinal axis of the tiop parallel to the transverse axis of the table surface.

Load the test -42-601 in the designated aircraft and secure it in accordance with the procedures outlined in 26 TOP 15 September FM The maximum external payload capabilities of U. Requirements for submission of design verification samples.